Industrial Parts

6 in Plastic Float Ball | 1/4-20 Internal Thread is a round plastic float ball for compatible float-valve and water-level control assemblies. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: round replacement float ball / tank ball.

• Float diameter: 6 in.

• Overall diameter: 6 in.

• Material of construction: plastic.

• Material detail: polyethylene.

• Shape: round float ball.

• Connection: internal.

• Connection type: threaded.

• Connection location: internal.

• Thread size: 1/4-20 internal thread.

• Compatible product type: float rods and float valves where the installed connection and float size match.

• Service role: provides buoyancy for compatible float-valve and water-level control assemblies.

• Ordering check: verify float diameter, 1/4-20 rod/thread connection, connection depth, buoyancy needs, tank clearance, water chemistry, operating temperature, and float-valve compatibility.

Related Parts & Compatibility Notes

• Related to 1/2 in and 3/4 in float-valve assemblies, but not a substitute for the valve body, seat, float arm, rod, or complete float-valve assembly.

• Use only where the original part is a 6 in plastic float ball and the installed rod or arm uses a matching 1/4-20 threaded connection.

• Do not substitute by diameter alone. Compare the old float ball, tank geometry, thread size, connection style, travel path, and shutoff level before installation.

Warnings & Restrictions

• Warning listed for this item family: Cancer and Reproductive Harm. See www.P65Warnings.ca.gov.

• Restriction note: this item is restricted for conveying or dispensing water for potable use.

• Verify water chemistry, tank clearance, thread engagement, float travel, and installed valve compatibility before use.

Machine Fitment & Industrial Use

Use for compatible dry-cleaning equipment, tank-level control, water-level control, and float-valve assemblies where the installed float is a 6 in plastic ball with a 1/4-20 internal threaded connection.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

1/2 in Full-Port FNPT Ball Valve | Chrome-Plated Brass | 600 psi CWP is a standard lever-handle full-port ball valve for compatible water, utility, air, and equipment service. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: manual two-way ball valve.

• Nominal valve size: 1/2 in.

• Pipe size: 1/2 in.

• Connection path: FNPT x FNPT.

• Connection type side 1: NPT female.

• Connection type side 2: NPT female.

• Body style: inline / straight.

• Valve structure: two-piece.

• Ball port style: full port.

• Ball material: chrome-plated brass.

• Body material: brass.

• Stem material: brass.

• Stem type: blowout resistant.

• Seat material: PTFE.

• Seal material: EPDM.

• Handle type: lever.

• Handle material: PVC and steel.

• Handle locking: non-locking.

• Handle color: yellow.

• Overall length: 2.05 in.

• Handle length: 3.82 in.

• Handle height: 2.04 in.

• Maximum operating pressure: 600 psi.

• Operating temperature range: 0 Degrees F to 400 Degrees F.

• For media: compatible utility service; verify media before installation.

• Standards reference: CSA, FM, MSS SP-110, UL 125, UL 1477, and UL 842.

• Restriction note: not intended for potable-water service unless the complete installed system is separately verified.

• Catalog note: separate from the 0904002 butterfly-handle ball-valve path and separate from the spring-loaded 1/2 in ball-valve path.

• Ordering check: verify pipe size, thread type, pressure, temperature, media, handle clearance, body style, and shutoff requirements before ordering.

Related Parts & Compatibility Notes

• Do not substitute for the 0904002 butterfly-handle ball valve, spring-loaded ball valve, float valve, check valve, or pneumatic valve unless the installed component and service conditions match.

• Use only where a standard 1/2 in FNPT full-port lever-handle ball valve is correct for the system.

Warnings & Restrictions

• Restriction note: this product is not intended for potable-water applications and has not been designed for low-lead Safe Drinking Water Act compliance.

• Combustible-gas and steam pressure ratings are not rated in the available technical data; verify media, code, and application before installation.

• Use qualified service personnel and confirm pressure, temperature, media compatibility, and handle clearance before installation.

Machine Fitment & Industrial Use

Use for compatible utility, water-control, air, and equipment-service locations where a standard 1/2 in FNPT full-port lever-handle ball valve is required.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

Parker Push-to-Connect Fitting | 1/4 in OD Tube x 1/8 in MNPT is a Parker push-to-connect fitting for compatible pneumatic, vacuum, automation, and equipment service. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: straight push-fit fitting / connector.

• Connection path: 1/4 in OD tube x 1/8 in MNPT.

• Tube outer diameter: 1/4 in.

• Pipe size: 1/8 in.

• Fitting side A connection type: push-to-connect.

• Fitting side B connection type: MNPTF.

• Fitting material: brass.

• Material grade: C36000.

• Finish/coating: nickel plated.

• Color: silver.

• Overall length: 7/8 in.

• Maximum operating pressure: 300 psi.

• Vacuum rating: 28 inHg.

• Operating temperature range: 0 Degrees F to 200 Degrees F.

• Compatible tube materials: polyethylene, polypropylene, polyurethane, rigid nylon, and semi-rigid nylon.

• Release ring material: nitrile rubber.

• Includes pre-applied thread sealant: yes.

• Standards reference: UL94 V-0.

• Application family: automotive, climate control, robotics, automation, industrial, lubrication, packaging, pneumatics, electronics, textile, and vacuum.

• For media type: air, gases, and oils.

• Restriction note: not intended for potable-water service unless the complete installed system is separately verified.

• Ordering check: verify tube OD, tube material, thread size, thread sealant, pressure, vacuum, temperature, media, and service location before ordering.

Related Parts & Compatibility Notes

• Do not substitute with SAE hose adapters, FIP/MIP conversion adapters, compression fittings, or pipe adapters unless every connection requirement matches.

• Use only where the tube OD, port thread, media, pressure, temperature, and fitting orientation match the installed pneumatic or equipment circuit.

Warnings & Restrictions

• Warning listed for this item family: Cancer and Reproductive Harm. See www.P65Warnings.ca.gov.

• Restriction note: this product is not intended for potable-water applications and has not been designed for low-lead Safe Drinking Water Act compliance.

• Verify tube material, media, air/gas/oil service, pressure, temperature, and installed environment before use.

Machine Fitment & Industrial Use

Use for compatible pneumatic, vacuum, automation, climate-control, and equipment-service circuits where a 1/4 in OD tube x 1/8 in MNPT push-to-connect fitting is required.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

Carbon Steel Gauge Syphon | 1/4 in MNPT x 1/4 in MNPT is a schedule 80 carbon steel pressure-gauge syphon for compatible steam and high-temperature gauge-protection service. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: pressure-gauge siphon / syphon / pigtail.

• Material: steel.

• Gauge case material reference: schedule 80 carbon steel.

• Connection path: 1/4 in male x 1/4 in male NPT.

• Connection size: 1/4 in.

• Connection type: NPT.

• Connection thread size: 1/4 in.

• Tube length: 4-9/16 in.

• Tube style: pigtail.

• Construction: seamless.

• Maximum internal pressure: 1,650 psi.

• Pressure/temperature reference: 1,650 psi at 630 Degrees F.

• Compatible process media: steam.

• Application: steam installations and applications above 100 Degrees F.

• Standards reference: CRN registered.

• NSF certified: yes.

• Corrosion resistance: not corrosion resistant.

• Ordering check: verify thread orientation, installed clearance, pressure, temperature, media, code/service requirements, and gauge compatibility before ordering.

Related Parts & Compatibility Notes

• Do not substitute for brass plumbing fittings, refrigeration adapters, or the pressure gauge itself.

• Use only where the installed gauge assembly requires a 1/4 in NPT steel pigtail syphon for steam or high-temperature service.

Warnings & Restrictions

• This steel syphon is not corrosion resistant; verify process media, environment, and corrosion exposure before installation.

• Use qualified service personnel and confirm code, pressure, temperature, steam-service, and gauge-protection requirements before installation.

Machine Fitment & Industrial Use

Use for compatible steam and high-temperature pressure-gauge protection where the installed gauge connection and process conditions match the listed specifications.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

Brass Conversion Adapter | 1/4 FIP x 5/16 MIP | 4 Pack is a brass conversion adapter set for compatible service, gauge, and equipment fitting work. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: brass conversion adapter.

• Package format: 4 adapters per pack.

• Material: brass.

• Connection path: 1/4 FIP x 5/16 MIP.

• Connection type: female flare x male flare.

• Side A: 1/4F.

• Side B: 5/16M.

• Use case: thread conversion where both connection standards match the installed service path.

• Service fit: used when a fitting path needs a compact brass conversion between a 1/4 female flare side and a 5/16 male flare side.

• Selection checkpoint: confirm the flare seat, thread form, male/female orientation, and required quantity before ordering.

• Pack note: sold as a 4-pack for service work where multiple adapters may be needed for the same repair or setup.

• Ordering check: verify thread size, thread type, flare sealing method, pressure, temperature, media, and installed fitting clearance before ordering.

Related Parts & Compatibility Notes

• Do not confuse with SAE hose adapters, MNPT push-to-connect fittings, compression fittings, or general pipe fittings.

• Use only where the installed component requires the listed female-flare to male-flare conversion path.

• A visually similar brass adapter may not seal if the flare angle, thread family, or male/female orientation differs.

Warnings & Restrictions

• Warning listed for this item family: Cancer and Reproductive Harm. See www.P65Warnings.ca.gov.

• Verify the application, media, pressure, temperature, and local requirements before installation.

Machine Fitment & Industrial Use

Use for verified equipment-service fitting conversions where the installed service path requires 1/4 FIP x 5/16 MIP brass adapters.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

Brass Hose Adapter | 1/4 SAE Male x 5/16 SAE Female is a brass hose and service adapter for compatible HVACR, refrigeration, mini-split, service-tool, and industrial hose connections. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: brass hose/service adapter.

• End style: flared ends for HVACR service use.

• Connection path: 1/4 in SAE male x 5/16 in SAE female.

• Input connection size: 5/16 in.

• Output connection size: 1/4 in.

• Overall length: 1-3/8 in.

• Temperature range: 0 Degrees F to 122 Degrees F.

• Use family: HVACR, mini-split, ductless, refrigeration, and service-tool connections where the hose and port match.

• Service fit: useful where a service hose, manifold, gauge hose, or mini-split service connection requires the listed SAE conversion.

• Selection checkpoint: SAE flare connections seal differently than pipe-thread fittings, so match the port style and sealing surface rather than choosing by diameter alone.

• Ordering check: verify refrigerant/service application, SAE thread form, sealing surface, pressure rating, service-tool compatibility, and installed clearance before ordering.

Related Parts & Compatibility Notes

• Do not substitute for pipe-thread adapters, push-to-connect fittings, compression fittings, or dry-cleaning machine valve fittings unless every connection and service condition matches.

• Use only where the service hose and service port match the listed SAE connection path.

• If the hose end, gauge manifold, or service port uses NPT, compression, push-to-connect, or another thread family, choose a different fitting.

Machine Fitment & Industrial Use

Use for compatible refrigeration and HVACR service work where a 1/4 in SAE male to 5/16 in SAE female adapter is required.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

3MROM413 Reverse Osmosis Membrane | 11 gpd 3-1/4 in Dia is a reverse-osmosis membrane cartridge for compatible under-sink RO water-filtration systems. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: quick-connect reverse-osmosis membrane cartridge.

• Public cartridge family: 3MROM413.

• Rated output: 11 gpd.

• Micron rating: 5 micron.

• Approximate diameter: 3-1/4 in.

• Approximate overall height: 14-7/8 in.

• Filter media/function: reverse-osmosis separation.

• Reduction claims shown for this cartridge family: cyst, lead, mercury, and volatile organic compounds.

• Pressure range: 40 psi minimum to 100 psi maximum.

• Temperature range: 40 Degrees F minimum to 100 Degrees F maximum.

• Service-life reference: 24 months under compatible system conditions.

• Standards reference: NSF.

• Compatible product type: under-sink reverse-osmosis water filter systems.

• Compatible system models to verify: 3MRO301, 3MRO401, and 3MRO501.

• Ordering check: verify the membrane path, cartridge markings, head style, pressure, temperature, output requirement, and system documentation before ordering.

Related Parts & Compatibility Notes

• Do not substitute with sediment, carbon, quick-connect support filters, or whole-house cartridges; this is a membrane-style RO component.

• This is separate from the 3MROP416-20A quick-connect filter cartridge and must match the membrane position in the installed RO system.

Warnings & Restrictions

• Restriction note: this cartridge family is third-party certified as compliant with Safe Drinking Water Act low-lead requirements for potable and non-potable water applications.

• Certification and compatibility still depend on the complete installed system, filter head, service conditions, local requirements, and maintenance interval.

Machine Fitment & Industrial Use

Use only where the existing RO system calls for this membrane family and the physical cartridge style, head connection, pressure, temperature, and output requirement match.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

3MROP416-20A Quick-Connect Water Filter | 0.5 gpm 4-3/8 in Dia is a quick-connect water filter cartridge for compatible under-sink, reverse-osmosis support, commercial utility, and equipment water-filtration systems. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: quick-connect water filter cartridge.

• Public cartridge family: 3MROP416-20A.

• Rated flow: 0.5 gpm.

• Approximate diameter: 4-3/8 in.

• Approximate overall height: 13-3/4 in.

• Filter media: carbon block.

• Pressure range: 25 psi minimum to 100 psi maximum.

• Temperature range: 40 Degrees F minimum to 100 Degrees F maximum.

• Service-life reference: 6 months under compatible system conditions.

• Standards reference: NSF.

• Compatible product type: under-sink reverse-osmosis water filter systems.

• Compatible system models to verify: 3MRO301, 3MRO401, and 3MRO501.

• Ordering check: verify the installed filter head, cartridge family, diameter, height, clearance, pressure, temperature, service interval, and required filtration claims before ordering.

Related Parts & Compatibility Notes

• Do not substitute with RO membrane cartridges, sediment-only cartridges, whole-house cartridges, or other filter families unless the installed head confirms compatibility.

• This is separate from the RO membrane listing; compare the old cartridge body, head style, diameter, height, and system documentation before ordering.

Warnings & Restrictions

• Restriction note: this cartridge family is third-party certified as compliant with Safe Drinking Water Act low-lead requirements for potable and non-potable water applications.

• Certification and compatibility still depend on the complete installed system, filter head, service conditions, local requirements, and maintenance interval.

Machine Fitment & Industrial Use

Use where the installed water-filtration system calls for this quick-connect cartridge family and the system pressure, temperature, head style, and service interval match.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.

Culligan RC-EZ-4 Quick Connect Water Filter | 0.5 gpm 0.5 Micron is a quick-connect replacement water filter cartridge for compatible under-sink, shop utility, and equipment water-filtration service. This listing is written as a technical Corbett Equipment catalog listing for dry-cleaning shops, commercial utility service, equipment maintenance, water treatment, refrigeration/HVACR service, pneumatic systems, steam/gauge service, and industrial maintenance where the installed component matches the specifications below.

Use this listing only after comparing the installed part, physical dimensions, connection style, material, operating conditions, and machine or system documentation.

Technical Specifications

• Component type: quick-connect replacement water filter cartridge.

• Public cartridge family: RC-EZ-4.

• Rated flow: 0.5 gpm.

• Filtration rating: 0.5 micron.

• Approximate dimensions: 2-3/4 in outside diameter x 12-1/2 in height.

• Service role: water filtration for compatible filter-head systems where the installed cartridge, lock style, clearance, and flow requirements match.

• Ordering check: verify the old cartridge markings, filter head, cartridge lock style, clearance, water pressure, flow requirement, and filtration requirement before ordering.

Related Parts & Compatibility Notes

• Do not substitute with another quick-connect cartridge, RO membrane, sediment filter, or carbon filter unless the installed filter head and system documentation confirm compatibility.

• Compare the old cartridge body, head style, cartridge markings, diameter, height, and service requirement before ordering.

Machine Fitment & Industrial Use

Use for compatible shop, equipment, and utility-water filtration where the installed system calls for the same cartridge family and physical connection.

For dry-cleaning equipment, verify against the actual machine, valve panel, boiler or water-treatment system, gauge assembly, filtration system, utility line, pneumatic circuit, refrigeration service port, or service hose before ordering. If the product is being used outside dry cleaning, confirm compatibility with the application and operating conditions before installation.

Installation & Ordering Verification

• Compare the product photo, installed component, size, connection style, and service location before ordering.

• Confirm pressure, flow, temperature, material, chemical exposure, media compatibility, clearance, and mounting for the actual system.

• Use qualified service personnel when installing pressure, steam, refrigeration, water, electrical, pneumatic, or equipment-control components.

• Send photos of the installed part, machine tag, and service location if fitment is uncertain.